pilot w kluczyku (alarm + centralny zamek)
Moderator: luk4s7
pilot w kluczyku (alarm + centralny zamek)
mam problem !!!
ostatnio staje się to zwyczajem
po wymianie baterii w kluczyku-pilocie nie działa sterowanie z pilota
centralny zamek działa jedynie po przekręceniu kluczyka w zamku
alarm się nie załącza
po wysunięciu kluczyka ze stacyjki immobiliser działa
czy po wymianie baterii trzeba jakoś kodować kluczyk ???
jeżeli tak, to jak to się robi ???
tylko serwis ???
ostatnio staje się to zwyczajem
po wymianie baterii w kluczyku-pilocie nie działa sterowanie z pilota
centralny zamek działa jedynie po przekręceniu kluczyka w zamku
alarm się nie załącza
po wysunięciu kluczyka ze stacyjki immobiliser działa
czy po wymianie baterii trzeba jakoś kodować kluczyk ???
jeżeli tak, to jak to się robi ???
tylko serwis ???
Re: pilot w kluczyku (alarm + centralny zamek)
Imobiliser jest urzadzeniem pasywnym (tzn. nie jest zasilany przez baterie w kluczyku). Dziala podobnie jak karty magnetyczne do otwierania drzwi. Może po prostu szlag trafi moduł otwierania dzrwi w kluczyku?
jjb
jjb
Re: pilot w kluczyku (alarm + centralny zamek)
tak po prostu ? po 3 latach ? niemożliwe (nie topiłem, nie rzucałem, etc.)jjb pisze:[...] Może po prostu szlag trafi moduł otwierania dzrwi w kluczyku?
Re: pilot w kluczyku (alarm + centralny zamek)
szkoda że mieszkasz tak daleko od wawy... Bo w Łomiankach jest magik który dorabia kluczę do samochodów... Każdych samochodów dużo taniej niż w serwisie... czasami 50 % taniej...
Re: pilot w kluczyku (alarm + centralny zamek)
Bardzo możliwe, że rozkodował ci się nadajnik w kluczyku. Wyjęcie starej baterii i założenie nowej należy wykonać w dość krótkim czasie. Ile to trwało u Ciebie?
Re: pilot w kluczyku (alarm + centralny zamek)
może to pomoże
http://toyota.auto.com.pl/forum/viewtop ... 2aa6599bcc" onclick="window.open(this.href);return false;
http://toyota.auto.com.pl/forum/viewtop ... 2aa6599bcc" onclick="window.open(this.href);return false;
Re: pilot w kluczyku (alarm + centralny zamek)
niestety nie pomogłoroso pisze:może to pomoże
http://toyota.auto.com.pl/forum/viewtop ... 2aa6599bcc" onclick="window.open(this.href);return false;
Re: pilot w kluczyku (alarm + centralny zamek)
nie dłużej niż 1 minutęmilczacy pisze:Bardzo możliwe, że rozkodował ci się nadajnik w kluczyku. Wyjęcie starej baterii i założenie nowej należy wykonać w dość krótkim czasie. Ile to trwało u Ciebie?
Re: pilot w kluczyku (alarm + centralny zamek)
Sprawdzałem w swoim manualu ale o czasie jaki jest na wymiane baterii nic nie piszą .... Jedna minuta to jednak długo w tym przypadku
Re: pilot w kluczyku (alarm + centralny zamek)
Czas raczej nie ma znaczenia, przynajmniej u mnie kuczyki bez baterii ze dwie godziny leżaly.
Samochód 2004 rok.
Samochód 2004 rok.
Re: pilot w kluczyku (alarm + centralny zamek)
no i nadal jestem w ciemnej du....e
może komuś się przyda procedura ponownego kodowania klucza j100 prod po 2003 r.
u mnie wszystko idzie do punktu 6, potem już nie reaguje
zupełnie już nie wiem o co chodzi, że nie załapuje
Program Remote: (sequence I – 2003+)
1. Start with the key out of the ignition, drivers door is open all others closed and
drivers door is unlocked.
2. Perform these steps within 5 seconds.
Insert the key into the ignition(Do NOT Turn) Pull key out.
Insert the key into the ignition(Do NOT Turn) Pull key out.
3. Perform these steps within 40 seconds.
Close then open the drivers door.
Close then open the drivers door.
Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds.
Close then open the drivers door.
Close then open the drivers door.
Insert the key into ignition and leave it in ignition.
Close the drivers door.
Turn the ignition to ON (Do NOT Start) then back to OFF.
Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically
indicating successful entry into programming mode.
Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds.
Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted.
Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.
może komuś się przyda procedura ponownego kodowania klucza j100 prod po 2003 r.
u mnie wszystko idzie do punktu 6, potem już nie reaguje
zupełnie już nie wiem o co chodzi, że nie załapuje
Program Remote: (sequence I – 2003+)
1. Start with the key out of the ignition, drivers door is open all others closed and
drivers door is unlocked.
2. Perform these steps within 5 seconds.
Insert the key into the ignition(Do NOT Turn) Pull key out.
Insert the key into the ignition(Do NOT Turn) Pull key out.
3. Perform these steps within 40 seconds.
Close then open the drivers door.
Close then open the drivers door.
Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds.
Close then open the drivers door.
Close then open the drivers door.
Insert the key into ignition and leave it in ignition.
Close the drivers door.
Turn the ignition to ON (Do NOT Start) then back to OFF.
Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically
indicating successful entry into programming mode.
Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds.
Press the lock and unlock buttons on the remote simultaneously for 1.5 seconds.
Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted.
Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.
Re: pilot w kluczyku (alarm + centralny zamek)
He, he, nic nie robiłem i dziś rankiem wczesnym, zupełnie przypadkiem odkryłem, że wszystko działa. Wystarczyło nacisnąć pilot. A już ponad 2 m-ce używałem kluczyka w zamku i się zdążyłem przyzwyczaić.lucjan pisze:no i nadal jestem w ciemnej du....e
A tu się samo naprawiło ??
Jak widać cierpliwość to lekarstwo na wiele przypadłości.
-
- Posty: 296
- Rejestracja: 11 mar 2019, 19:55
- Auto: Toyota Land Cruiser KDJ95 2001 5D.
- Kontakt:
Re: pilot w kluczyku (alarm + centralny zamek)
Czy taki zanik działania pilota się powtarza? Czy w jakiś konkretnych sytuacjach?